MAX351CSE-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX351 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX351CSE-T Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio of multiplexer to demultiplexer circuits. Temperatures around 0°C~70°C TA are extended for operation. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. There are 16 pins injected into the electronic part body. The analog switch ics are built using SPST - NC switching circuits. There are 4 circuits in this switch device. Look for analog switch ic variants by searching with MAX351. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 30V volts for the multiplexer. An effective Dual, Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 10V. A voltage higher than 100pA may cause damage to the switch multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 20V. You should attach at least 4.5V voltage if you are using dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. There is a voltage range of 20V operating voltages for the electrical part.
MAX351CSE-T Features
1 Channels
Switch Circuit: SPST - NC
MAX351CSE-T Applications
There are a lot of Maxim Integrated MAX351CSE-T Analog Switches & Multiplexers ICs applications.
- Multi-Line E1 Interface Cards
- High reliability control systems
- ISDN NT1/TA
- Mechanical reed relay replacement
- Precision test equipment
- Audio and video signal routing
- Audio and video switching
- Industrial
- Modems
- Microprocessor Controlled Analog Systems
