banner_page

MAX352CPE+

175ns, 145ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX352 16 Pins 250pA 15V 16-DIP (0.300, 7.62mm)


  • Manufacturer: Maxim Integrated
  • Nocochips NO: 503-MAX352CPE+
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 205
  • Description: 175ns, 145ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX352 16 Pins 250pA 15V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Mount Through Hole
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Number of Pins 16
Operating Temperature 0°C~70°C TA
Packaging Tube
Published 2002
JESD-609 Code e3
Pbfree Code yes
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
ECCN Code EAR99
Resistance 35Ohm
Terminal Finish Matte Tin (Sn)
Subcategory Multiplexer or Switches
Max Power Dissipation 842mW
Technology CMOS
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 15V
Base Part Number MAX352
Output SEPARATE OUTPUT
Pin Count 16
Operating Supply Voltage 20V
Power Supplies 512/+-15V
Number of Channels 4
Max Supply Voltage 30V
Min Supply Voltage 10V
Nominal Supply Current 100pA
Max Supply Current 100pA
Throw Configuration SPST
Turn On Delay Time 175 ns
Voltage - Supply, Single/Dual (±) 10V~30V ±4.5V~20V
Supply Type Dual, Single
Neg Supply Voltage-Nom (Vsup) -15V
Turn-Off Delay Time 145 ns
Max Dual Supply Voltage 20V
On-State Resistance (Max) 35Ohm
Min Dual Supply Voltage 4.5V
Multiplexer/Demultiplexer Circuit 1:1
Off-state Isolation-Nom 68 dB
Current - Leakage (IS(off)) (Max) 250pA
Channel Capacitance (CS(off), CD(off)) 9pF 9pF
On-state Resistance Match-Nom 2Ohm
Switch Circuit SPST - NO
Switch Time (Ton, Toff) (Max) 175ns, 145ns
Charge Injection 5pC
Channel-to-Channel Matching (ΔRon) 2 Ω (Max)
Crosstalk -85dB @ 1MHz
Switching BREAK-BEFORE-MAKE
Normal Position NO
Length 19.175mm
Width 7.62mm
Radiation Hardening No
REACH SVHC Unknown
RoHS Status ROHS3 Compliant
Lead Free Lead Free

MAX352CPE+ Overview


The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. In Through Hole, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Extended operating temperature around 0°C~70°C TA. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 4 channels. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. A total of 16 pins are injected into the body of the electronic part. SPST - NO switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with MAX352. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage fed to the electronic component should be 10V. Put voltage above 100pA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 20V. The voltage should be at least 4.5V if you are using dual power supplies. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. 20V operating voltages are supported by the electronic component.

MAX352CPE+ Features


4 Channels
Switch Circuit: SPST - NO

MAX352CPE+ Applications


There are a lot of Maxim Integrated MAX352CPE+ Analog Switches & Multiplexers ICs applications.

  • Remote wireless modules
  • Automotive applications
  • Routers
  • Low-Voltage
  • Intelligent PBX
  • Communications systems
  • Central office
  • Switching Systems
  • Signal routing between systems
  • Battery Powered Instruments

Write a review

Note: HTML is not translated!
    Bad           Good