MAX352CSE
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX352 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 35Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX352CSE Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature around 0°C~70°C TA extended. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. An electrical component like this is included in the 16 series. A SPST - NO switching circuit is used to build these analog multiplexers. 4 circuits are used in this analogue multiplexer. Try searching for MAX352 variants of the analog switch ic. This switch device is a typical Multiplexer or Switches. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
MAX352CSE Features
1 Channels
Switch Circuit: SPST - NO
MAX352CSE Applications
There are a lot of Maxim Integrated MAX352CSE Analog Switches & Multiplexers ICs applications.
- FTTH
- USB 1.1 signal switching circuits
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Optical Applications
- Microprocessor Controlled Analog Systems
- Switching Systems
- Fault Tolerant Systems
- Video switching
- Communication systems
