MAX352EPE
| Parameters | |
|---|---|
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | MAX352 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
MAX352EPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. It is mounted in the position Through Hole. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. In total, there are 16 terminations. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. A total of 16 pins are injected into the electrical part body. Multiplexers built on a SPST - NO switching circuit are built. There are 4 circuits in this multiplexer. MAX352 can be used to search for analog multiplexer variants. Internally, this switch multiplexer has a resistance of 35Ohm. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 30V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 10V. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX352EPE Features
1 Channels
Switch Circuit: SPST - NO
MAX352EPE Applications
There are a lot of Maxim Integrated MAX352EPE Analog Switches & Multiplexers ICs applications.
- Imaging
- DVD-R
- Video signal routing
- RGB switches
- Audio and video routing
- Fault Tolerant Systems
- High speed data transmission line cards
- Communications systems
- 65 V DACs
- T1/E1 Terminals
