MAX352ESE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX352 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 512/+-15V |
| Number of Channels | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX352ESE+ Overview
Packed in 16-SOIC (0.154, 3.90mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. The electronic part provides high-quality output because it has 4 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. There are 16 pins injected into the electronic part body. A SPST - NO switching circuit is used for these analog switches. Using the MAX352 search parameter, you can discover variants of the switch. An switch multiplexer with 35Ohm internal resistance has a value of 35Ohm. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 30V. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage the electronic part should receive is 10V. When the digital multiplexer is charged above 100pA, damage can occur. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. The voltage should be at least 4.5V if you are using dual power supplies. This analog switch ic utilizes SEPARATE OUTPUT output. A voltage of 20V can be used to operate the electronic component.
MAX352ESE+ Features
4 Channels
Switch Circuit: SPST - NO
MAX352ESE+ Applications
There are a lot of Maxim Integrated MAX352ESE+ Analog Switches & Multiplexers ICs applications.
- Power routing
- Battery Powered Instruments
- Public switching systems
- Relay Replacement
- E1 Multiplexer
- Modems
- DSUs
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Channel Banks
- Industrial and process control systems
