MAX352ESE+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX352 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 100pA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX352ESE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. A total of 16 terminations have been recorded. A 1 channel electronic part produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. A total of 16 pins are injected into the body of the electronic part. SPST - NO switching circuits are used in these analog switch ics. A total of 4 circuits make up this switch device. Look for analog switch ic variants by searching with MAX352. In this multiplexer, the internal resistance is 35Ohm. Datasheets for 16 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 30V to the switch device in normal circumstances. 10V should be the lowest voltage fed to the electronic component. It may damage the digital multiplexer if the voltage is higher than 100pA. For this switch, a dual supply voltage is feasible, but it must not exceed 20VYou should attach at least 4.5V voltage if you are using dual power supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. This electrical part is compatible with 20V operating voltages.
MAX352ESE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX352ESE+T Applications
There are a lot of Maxim Integrated MAX352ESE+T Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Isolation
- Public switching systems
- MP3 players
- Voice over IP/DSL – Integrated Access Devices, Smart
- Medical systems
- Sample hold systems
- Cable Modem
- Low-Voltage
- Microprocessor controlled systems
