MAX353CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2002 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX353 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Qualification Status | Not Qualified |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 35Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Length | 19.175mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
MAX353CPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is achieved by using advanced packaging method Tube. It is mounted in the position Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. Totally, there are 16 terminations. A 1 channel electronic part produces high-quality output. An 15V voltage supply should allow the electrical part to be turned on and run. It is injected into the electrical part body with 16 pins. These analog multiplexers are built based on SPST - NO/NC switching circuits. 4 circuits are used in this analogue multiplexer. Try searching for MAX353 variants of the analog switch ic. This switch device is a typical Multiplexer or Switches. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX353CPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX353CPE Applications
There are a lot of Maxim Integrated MAX353CPE Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- E1 Multiplexer
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Microprocessor Controlled Analog Systems
- Switching Systems
- High-Voltage
- PCMCIA cards
- Digital cross connects (DSX-1)
- SDH/SONET multiplexers
- Low-Voltage
