MAX353CSE+T
| Parameters | |
|---|---|
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX353 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 18V |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 175ns, 145ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
MAX353CSE+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Increasing operating temperature to around 0°C~70°C TA. The total number of terminations is 16. This electronic part offers high-quality output due to its 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. The electronic part body is injected with 16 pins. A SPST - NO/NC switching circuit is used to build these analog multiplexers. It consists of 4 circuits. Try searching with MAX353 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 35Ohm. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 30V. 10V should be the lowest voltage fed to the electronic component. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch device's dual supply capability, its voltage should not exceed 20V. If you are using dual power supplies, you should attach at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating voltages range from 18V.
MAX353CSE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX353CSE+T Applications
There are a lot of Maxim Integrated MAX353CSE+T Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Avionics test equipment
- CSU
- Industrial control systems
- Automatic test equipment
- Fiber In The Loop (FITL)
- Low-Voltage
- USB 1.1 signal switching circuits
- Avionics
- Data switching
