MAX354CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 350Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX354 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 300μA |
| Throw Configuration | DPST |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 250 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 350Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 1.6pF 11pF |
| On-state Resistance Match-Nom | 7Ohm |
| Switch Time (Ton, Toff) (Max) | 250ns, 200ns |
| Charge Injection | 80pC |
| Channel-to-Channel Matching (ΔRon) | 7 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 300ns |
| Signal Current-Max | 0.03A |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX354CPE+ Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Through Hole. 8:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around 0°C~70°C TA. The total number of terminations is 16. Due to its 8 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. A total of 16 pins are injected into the electrical part body. There are 1 circuits in this switch device. Use MAX354 to search for variants of the digital switches. This digital multiplexer has 350Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. Users shouldn't supply more than 36V voltage to the switch device. Analog switch ics with Dual, Single supply type are cost-effective. There should be 4.5V voltage fed to the electrical part below 4.5V. 300μA current would be enough for this multiplexer to operate. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 18V. When using dual power supplies, you should attach at least 4.5V. The electronic component can function from 28V.
MAX354CPE+ Features
8 Channels
300μA Supply Current
MAX354CPE+ Applications
There are a lot of Maxim Integrated MAX354CPE+ Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Voice over IP/DSL – Integrated Access Devices, Smart
- Imaging
- High reliability control systems
- Avionics
- Residential Gateways, Home Gateway/Router
- Fiber In The Loop (FITL)
- Communication systems
- Relay replacements
- Avionics and Military Systems
