MAX355CPE+
| Parameters | |
|---|---|
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 350Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 1.6pF 5pF |
| On-state Resistance Match-Nom | 7Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 250ns, 200ns |
| Charge Injection | 80pC |
| Channel-to-Channel Matching (ΔRon) | 7 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 300ns |
| Signal Current-Max | 0.03A |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 350Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX355 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 300μA |
| Throw Configuration | 4PST |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 250 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
MAX355CPE+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 4:1. Operational temperature extended around 0°C~70°C TA. A total of 16 terminations have been recorded. A high-quality output is provided by the electrical component's 4 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. It is part of the design of the 16 series that this electronic component is included. The analog switch ics are built using SP4T switching circuits. The circuits in this analogue multiplexer number 2. Use MAX355 to search for variants of the digital switches. In this multiplexer, the internal resistance is 350Ohm. The datasheets for the 16 pins explain the functions. normally, users should not supply switches with voltages higher than 36V. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended to use 4.5V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 300μA current. If put voltage greater than 18V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 4.5V voltage attached. Operating voltages of 28V are compatible with the electrical part.
MAX355CPE+ Features
4 Channels
Switch Circuit: SP4T
300μA Supply Current
MAX355CPE+ Applications
There are a lot of Maxim Integrated MAX355CPE+ Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Relay replacements
- Cable PC
- Video signal routing
- Communication systems
- Audio and video signal routing
- ATM
- High speed data transmission line cards
- Residential Gateways, Home Gateway/Router
- Multi-Line E1 Interface Cards
