MAX355EWE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 350Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Power Dissipation | 762mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX355 |
| Pin Count | 16 |
| Operating Supply Voltage | 28V |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Operating Supply Current | 300μA |
| Propagation Delay | 250 ns |
| Turn On Delay Time | 250 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~18V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 350Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 100 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 1.6pF 5pF |
| On-state Resistance Match-Nom | 7Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 250ns, 200ns |
| Charge Injection | 80pC |
| Channel-to-Channel Matching (ΔRon) | 7 Ω |
| Crosstalk | -92dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 400ns |
| Switch-off Time-Max | 300ns |
| Signal Current-Max | 0.03A |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
MAX355EWE Overview
Due to its 16-SOIC (0.295, 7.50mm Width) packaging, the electronic part is convenient for international shipping. High reliability is ensured by the advanced packaging method Tube. This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 4:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. 16 terminations have been made so far. A electrical component with 4 channels is capable of high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. Multiplexers built on a SP4T switching circuit are built. A total of 2 circuits make up this switch device. Using the MAX355 search parameter, you can discover variants of the switch. This digital multiplexer has 350Ohm internal resistance. The functions of 16 pins can be found in the datasheets. A voltage higher than 36V should not normally be supplied to the switches. Dual, Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 4.5V. The analogue multiplexer could operate on 300μA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 18V. A dual power supply should have at least 4.5V voltage attached. The electrical part can be operated at 28V voltage levels.
MAX355EWE Features
4 Channels
Switch Circuit: SP4T
300μA Supply Current
MAX355EWE Applications
There are a lot of Maxim Integrated MAX355EWE Analog Switches & Multiplexers ICs applications.
- Multiplexers
- Private Branch Exchange (PBX)
- SONET
- Public switching systems
- PDAs
- Isolation
- DVD-R
- FTTH
- PCMCIA cards
- Cable Telephony – NIU, Set-Top Box, Home Side Box
