MAX361CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | MAX361 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | +-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 30V |
| Min Supply Voltage | 10V |
| Nominal Supply Current | 15μA |
| Max Supply Current | 15μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX361CPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around 0°C~70°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. Based on SPST - NC switching circuits, these analog multiplexers work. There are 4 circuits in this multiplexer. Try searching for the analog switch ic with MAX361 if you are looking for variants. In this multiplexer, the internal resistance is 85Ohm. The datasheets for the 16 pins explain the functions. In this analog multiplexer, the value is Multiplexer or Switches. normally, users should not supply switches with voltages higher than 30V. A cost-effective Dual, Single supply type analogue multiplexer. 10V should be the lowest voltage fed to the electronic component. It may damage the digital multiplexer if the voltage is higher than 15μA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 20V. When using dual power supplies, you should attach at least 4.5V. There are SEPARATE OUTPUT outputs on this analog switch ic. It can operate from 20V operating voltages.
MAX361CPE Features
1 Channels
Switch Circuit: SPST - NC
MAX361CPE Applications
There are a lot of Maxim Integrated MAX361CPE Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- Digital access cross connects
- Wireless Local Loop
- Microprocessor Controlled Analog Systems
- Access Concentrators
- Private Branch Exchange (PBX)
- E1 Network Equipment
- Transmit
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Precision data acquisition
