Parameters |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
250ns, 120ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω (Max) |
Crosstalk |
-100dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NO |
Length |
19.175mm |
Width |
7.62mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2004 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
85Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Base Part Number |
MAX362 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
12/+-15V |
Number of Channels |
4 |
Max Supply Voltage |
20V |
Min Supply Voltage |
4.5V |
Nominal Supply Current |
15μA |
Max Supply Current |
100μA |
Throw Configuration |
SPST |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
170 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
MAX362CPE+ Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. To ensure high reliability, a new packaging method Tube is used. Mounted in Through Hole is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around 0°C~70°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 4 channels. A 15V voltage supply should turn on and run the electronic component. It is injected into the electrical part body with 16 pins. A SPST - NO switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with MAX362. The internal resistance of this digital multiplexer is 85Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 20V. The digital multiplexer has a low cost Dual, Single supply. The lowest voltage the electronic part should receive is 4.5V. A voltage higher than 100μA may cause damage to the switch multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 20V. With dual power supplies, you should attach at least 4.5V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX362CPE+ Features
4 Channels
Switch Circuit: SPST - NO
MAX362CPE+ Applications
There are a lot of Maxim Integrated MAX362CPE+ Analog Switches & Multiplexers ICs applications.
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- E1 Network Equipment
- Battery Powered Systems
- Digital access cross connects
- Sample-and-hold systems
- Switching Systems
- High reliability control systems
- Access Concentrators
- SONET/SDH ADM
- Cable PC