MAX362CSE+
| Parameters | |
|---|---|
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX362 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 15μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 170 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
MAX362CSE+ Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tube is used. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature around 0°C~70°C TA extended. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. An electrical component of this type can be found in the 16 series. SPST - NO switching circuits are used in these analog switch ics. It consists of 4 circuits. Try searching with MAX362 if you're looking for variants. It has an internal resistance of 85Ohm. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 20V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage the electronic part should receive is 4.5V. The switch multiplexer may be damaged if it is exposed to voltage greater than 100μA. If put voltage greater than 20V on the multiplexer, damage may be caused to the device. For dual power supplies, a voltage of at least 4.5V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX362CSE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX362CSE+ Applications
There are a lot of Maxim Integrated MAX362CSE+ Analog Switches & Multiplexers ICs applications.
- Private Branch Exchange (PBX)
- Low-Voltage
- E1 Multiplexer
- Video switching
- Imaging
- SONET/SDH ADM
- Channelized and Unchannelized DS3 applications
- Sample-and-hold systems
- ATM
- USB 1.1 signal switching circuits
