MAX362ESE
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2004 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 85Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX362 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Power Supplies | 12/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 20V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 15μA |
| Max Supply Current | 100μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 170 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX362ESE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. There is an analog multiplexer mounted in position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. There are 16 terminations totally. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 15V voltage supply. A total of 16 pins are injected into the body of the electronic part. On the other hand, analog switches can be constructed using SPST - NO switching circuits. This multiplexer is composed of 4 circuits. MAX362 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 85Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. A voltage higher than 20V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. A low voltage of 4.5V should be applied to the electronic component. It may damage the digital multiplexer if the voltage is higher than 100μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. It is recommended that you attach at least 4.5V to your dual power supply.
MAX362ESE Features
1 Channels
Switch Circuit: SPST - NO
MAX362ESE Applications
There are a lot of Maxim Integrated MAX362ESE Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- MP3 players
- PDH Multiplexers
- E1 Multiplexer
- Audio/video switches
- 65 V DACs
- Cell phones
- PDAs
- Channelized and Unchannelized DS3 applications
