MAX365EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 85Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | ALSO OPERATES WITH 10 V TO 30 V SINGLE SUPPLY |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Base Part Number | MAX365 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 512/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 24V |
| Min Supply Voltage | 10.8V |
| Voltage - Supply, Single/Dual (±) | 10V~30V ±4.5V~20V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 85Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 60 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 250ns, 120ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω (Max) |
| Crosstalk | -100dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 250ns |
| Switch-off Time-Max | 170ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX365EPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. In Through Hole, you'll find this switch device. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 15V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. The circuits in this analogue multiplexer number 4. Use MAX365 to search for variants of the digital switches. There is 85Ohm internal resistance in this digital multiplexer. Datasheets for functions of 16 pins are available. Multiplexer or Switches is a typical switch device. It is generally not recommended to supply a voltage higher than 24V to the switch device in normal circumstances. It is recommended that the electrical component receives a voltage of 10.8V. For this switch, a dual supply voltage is feasible, but it must not exceed 20VWith dual power supplies, you should attach at least 4.5V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Don't forget the additional features of this electronic part, such as: ALSO OPERATES WITH 10 V TO 30 V SINGLE SUPPLY.
MAX365EPE Features
1 Channels
Switch Circuit: SPST - NO
Additional Features: ALSO OPERATES WITH 10 V TO 30 V SINGLE SUPPLY
MAX365EPE Applications
There are a lot of Maxim Integrated MAX365EPE Analog Switches & Multiplexers ICs applications.
- Relay Replacement
- Sample hold systems
- Access Concentrators
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Ultrasound
- Channel Banks
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- RGB switches
- Multi-Line E1 Interface Cards
- Signal routing between systems
