Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-WQFN Exposed Pad |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1995 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
85Ohm |
Terminal Finish |
Tin (Sn) |
Additional Feature |
ALSO OPERATES WITH 10 V TO 30 V SINGLE SUPPLY |
Max Power Dissipation |
696mW |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.8mm |
Base Part Number |
MAX365 |
Pin Count |
16 |
Operating Supply Voltage |
20V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
24V |
Min Supply Voltage |
10.8V |
Nominal Supply Current |
100pA |
Max Supply Current |
100pA |
Throw Configuration |
SPST |
Turn On Delay Time |
250 ns |
Voltage - Supply, Single/Dual (±) |
10V~30V ±4.5V~20V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
120 ns |
Max Dual Supply Voltage |
20V |
On-State Resistance (Max) |
85Ohm |
Min Dual Supply Voltage |
4.5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 4pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
250ns, 120ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω (Max) |
Crosstalk |
-100dB @ 1MHz |
Switch-off Time-Max |
170ns |
Height Seated (Max) |
0.8mm |
Length |
5mm |
Width |
5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX365ETE+ Overview
This electronic part is conveniently packaged in 16-WQFN Exposed Pad, making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. 16 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. Based on SPST - NO switching circuits, these analog multiplexers work. Circuits number 4 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX365. An switch multiplexer with 85Ohm internal resistance has a value of 85Ohm. Please refer to the datasheets for 16 pins functions. In a normalsituation, users should not supply the switches with voltage higher than 24V. A cost-effective Dual, Single supply type analogue multiplexer. 10.8V is the lowest voltage that should be fed to the electronic electronic part. If put voltage greater than 100pA on the device, damage may be caused to the analogue multiplexer. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. The electrical part can be operated at 20V voltage levels. Don't miss this electronic component's additional features, such as: ALSO OPERATES WITH 10 V TO 30 V SINGLE SUPPLY.
MAX365ETE+ Features
1 Channels
Switch Circuit: SPST - NO
Additional Features: ALSO OPERATES WITH 10 V TO 30 V SINGLE SUPPLY
MAX365ETE+ Applications
There are a lot of Maxim Integrated MAX365ETE+ Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Transmit
- DVD-R
- Automotive applications
- Isolation
- T1/E1 Terminals
- Mechanical reed relay replacement
- Optical Applications
- Audio and video signal routing
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8