MAX378CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX378 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| On-State Resistance (Max) | 3.5kOhm |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 25pF |
| Switch Time (Ton, Toff) (Max) | 400ns, 300ns (Typ) |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Neg Supply Voltage-Min (Vsup) | -4.5V |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 4.572mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
MAX378CPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. In Through Hole, you'll find this switch device. There is 8:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around 0°C~70°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 8 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 16 series of products. Circuits number 1 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX378. The analog multiplexer shown here is a typical Multiplexer or Switches. An analog IC with the number SINGLE-ENDED MULTIPLEXER is integrated into this board. Providing power to the analogue multiplexer requires a voltage of 4.5VV.
MAX378CPE Features
8 Channels
MAX378CPE Applications
There are a lot of Maxim Integrated MAX378CPE Analog Switches & Multiplexers ICs applications.
- Digital Cross-Connects
- E1 Multiplexer
- RGB switches
- Remote wireless modules
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Microprocessor controlled systems
- Power routing
- SONET
- 65 V DACs
- FTTH
