MAX379EPE
| Parameters | |
|---|---|
| Switch Time (Ton, Toff) (Max) | 400ns, 300ns (Typ) |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 1000ns |
| Switch-off Time-Max | 1000ns |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 3.5kOhm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX379 |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Operating Supply Current | 1mA |
| Turn On Delay Time | 1 μs |
| Logic Function | Multiplexer |
| Supply Type | Dual |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 300 ns |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3.5kOhm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 12pF |
| Switch Circuit | SP4T |
MAX379EPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Through Hole. 4:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. There are 16 terminations totally. This electronic part offers high-quality output due to its 4 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 16 series. Circuits based on SP4T switching are used to construct these analog switch ics. Circuits number 2 make up this analogue multiplexer. Use MAX379 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 3.5kOhm. Please refer to the datasheets for 16 pins functions. Dual supply type digital switch with a low cost. In order to operate this switch device, it would need a current of 1mA. For this switch, a dual supply voltage is feasible, but it must not exceed 18VFor dual power supplies, a voltage of at least 4.5V should be attached. The electrical part can be operated at 15V voltage levels.
MAX379EPE Features
4 Channels
Switch Circuit: SP4T
1mA Supply Current
MAX379EPE Applications
There are a lot of Maxim Integrated MAX379EPE Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Frame Relay Equipment
- Residential Gateways, Home Gateway/Router
- Digital access cross connects
- SDH/SONET multiplexers
- Industrial and process control systems
- Signal routing between systems
- High reliability control systems
- Fault Tolerant Systems
- Central office
