MAX381CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | +-5V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 8V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 60nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 100ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX381CPE Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. This analog switch is mounted in Through Hole. 1:1 is the ratio between multiplexers and demultiplexers. Around 0°C~70°C TA is the extended operating temperature. 16 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Based on SPST - NO switching circuits, these analog multiplexers work. A total of 2 circuits make up this switch device. The internal resistance of this digital multiplexer is 35Ohm. The datasheets for the 16 pins explain the functions. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 8V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. 3V is the lowest voltage the electrical component should receive. This digital switch can be operated with a current of 60nA. A digital multiplexer may suffer damage if voltage is applied above 1μA. There is no problem with using dual supply voltage, but it should not exceed 8V. It is recommended that you attach at least 3V to your dual power supply. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
MAX381CPE Features
1 Channels
Switch Circuit: SPST - NO
60nA Supply Current
MAX381CPE Applications
There are a lot of Maxim Integrated MAX381CPE Analog Switches & Multiplexers ICs applications.
- Industrial
- Audio and video switching
- Multiplexers
- Microprocessor Controlled Analog Systems
- Public switching systems
- ISDN NT1/TA
- DVD-R
- Automatic test equipment
- Automotive applications
- Cell phones
