Parameters |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
400 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
200pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
175ns, 100ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
175ns |
Switch-off Time-Max |
100ns |
Length |
19.175mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mount |
Through Hole |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1995 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Base Part Number |
MAX383 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
8V |
Power Supplies |
+-5V |
Number of Channels |
1 |
Number of Circuits |
2 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2.7V |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
150 ns |
Voltage - Supply, Single/Dual (±) |
3V~15V ±3V~8V |
Supply Type |
Dual, Single |
MAX383CPE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Through Hole. Multiplexers and demultiplexers have the same number of circuits 2:1. Around 0°C~70°C TA is the extended operating temperature. In total, there have been 16 terminations. The electronic part delivers high-quality output through its 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. An electrical component like this is included in the 16 series. Based on SPDT switching circuits, these analog multiplexers work. There are 2 circuits in this multiplexer. Try searching with MAX383 if you're looking for variants. Analog switches have 35Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16V. An effective Dual, Single supply digital multiplexer. 2.7V is the lowest voltage that should be fed to the electronic electronic part. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 8VFor dual power supplies, a voltage of at least 3V should be attached. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. The electronic component can function from 8V.
MAX383CPE+ Features
1 Channels
Switch Circuit: SPDT
MAX383CPE+ Applications
There are a lot of Maxim Integrated MAX383CPE+ Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Fiber In The Loop (FITL)
- Optical Applications
- Industrial and process control systems
- Cross Connects
- HDTV
- Precision test equipment
- E1 Network Equipment
- Communication systems
- Low-Voltage