MAX383CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX383 |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| High Level Output Current | 30mA |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 175ns, 100ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Switch-off Time-Max | 100ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX383CSE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. High reliability is ensured by the advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Operation at a temperature around 0°C~70°C TA. Total terminations are 16. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. As part of its design, the 16 series is equipped with this electronic component. A SPDT switching circuit is used to build these analog multiplexers. The multiplexer consists of 2 circuits. If you are looking for variants of the digital switch, trying search with MAX383. This digital multiplexer has 35Ohm internal resistance. For functions related to 16 pins, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. When using dual power supplies, you should attach at least 3V. A voltage of 8V can be used to operate the electronic component.
MAX383CSE+T Features
1 Channels
Switch Circuit: SPDT
MAX383CSE+T Applications
There are a lot of Maxim Integrated MAX383CSE+T Analog Switches & Multiplexers ICs applications.
- Intelligent PBX
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Video signal routing
- E1 Network Equipment
- Audio signal routing
- Central office
- Precision instrumentation
- Modems
- Microprocessor controlled systems
- Audio and video routing
