MAX385CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX385 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 400 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 100ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 175ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NO |
| Length | 19.175mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX385CPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tube. Through Hole is where this multiplexer is located. There is 2:1 ratio between the number of multiplexers and demultiplexers. Temperatures around 0°C~70°C TA are extended for operation. A total of 16 terminations have been recorded. The electronic part delivers high-quality output through its 2 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. The analog switch ics are built using DPST - NO switching circuits. A total of 2 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with MAX385. Internally, this switch multiplexer has a resistance of 35Ohm. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 16V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch's dual supply capability, its voltage should not exceed 8V. In the case of dual power supplies, you should connect at least 3V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. A voltage of 5V can be used to operate the electronic component.
MAX385CPE Features
2 Channels
Switch Circuit: DPST - NO
MAX385CPE Applications
There are a lot of Maxim Integrated MAX385CPE Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Automatic test equipment
- Ultrasound
- Intelligent PBX
- Video signal routing
- Data switching
- High speed data transmission line cards
- HDTV
- Medical Instrumentation
- Digital access cross connects
