MAX385CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1995 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | MAX385 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Power Supplies | +-5V |
| Number of Channels | 2 |
| Number of Circuits | 2 |
| Max Supply Voltage | 8V |
| Min Supply Voltage | 3V |
| Nominal Supply Current | 10nA |
| Max Supply Current | 1μA |
| Throw Configuration | DPST |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | DPST - NO |
| Switch Time (Ton, Toff) (Max) | 175ns, 100ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX385CSE+ Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around 0°C~70°C TA is the extended operating temperature. In total, there have been 16 terminations. A 2 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. This electrical component is included in the 16 series of products. A DPST - NO switching circuit is used for these analog switches. A 2 circuit is present in this switch device. Look for analog switch ic variants by searching with MAX385. Internally, this switch multiplexer has a resistance of 35Ohm. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 8V. An effective Dual, Single supply digital multiplexer. It is recommended that the electrical component receives a voltage of 3V. Putting voltage greater than 1μA on the multiplexer may cause damage. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 8V. When using dual power supplies, you should attach at least 3V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number.
MAX385CSE+ Features
2 Channels
Switch Circuit: DPST - NO
MAX385CSE+ Applications
There are a lot of Maxim Integrated MAX385CSE+ Analog Switches & Multiplexers ICs applications.
- Medical systems
- Avionics
- Communication systems
- Wireless Local Loop
- Voice over IP/DSL – Integrated Access Devices, Smart
- E1 Multiplexer
- Automatic test equipment
- Fiber to the Home
- RGB switches
- Existing multiplexer applications (both fault-protected and nonfault-protected)
