MAX388CWG
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Resistance | 3kOhm |
| Max Power Dissipation | 941mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | MAX388 |
| Pin Count | 24 |
| JESD-30 Code | R-PDSO-G24 |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Operating Supply Current | 2mA |
| Throw Configuration | SP8T |
| Propagation Delay | 1 μs |
| Turn On Delay Time | 1.5 μs |
| Logic Function | Multiplexer |
| Supply Type | Dual |
| Supply Current-Max (Isup) | 2.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 1 μs |
| Max Dual Supply Voltage | 18V |
| On-State Resistance (Max) | 3kOhm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 25pF |
| On-state Resistance Match-Nom | 300Ohm |
| Switch Time (Ton, Toff) (Max) | 1.5μs, 1μs |
| Charge Injection | 55pC |
| Channel-to-Channel Matching (ΔRon) | 300 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Voltage - Supply, Dual (V±) | ±4.5V~18V |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX388CWG Overview
The electronic part can be shipped overseas conveniently because it is packaged in 24-SOIC (0.295, 7.50mm Width). The advanced packaging method Tube provides high reliability. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 8:1. Around 0°C~70°C TA is the extended operating temperature. 24 terminations have been made so far. The electronic part delivers high-quality output through its 8 channels. With a 15V voltage supply, the electrical component should be turned on and run. As part of its design, the 24 series is equipped with this electronic component. 1 circuits are used in this analogue multiplexer. Try searching for MAX388 variants of the analog switch ic. The internal resistance of this digital multiplexer is 3kOhm. Analog switch ics with Dual supply type are cost-effective. For this multiplexer to operate, 2mA current would be sufficient. There is no problem with using dual supply voltage, but it should not exceed 18V. In the case of dual power supplies, you should connect at least 4.5V. Operating voltages of 15V are compatible with the electrical part.
MAX388CWG Features
8 Channels
2mA Supply Current
MAX388CWG Applications
There are a lot of Maxim Integrated MAX388CWG Analog Switches & Multiplexers ICs applications.
- FTTH
- Fiber In The Loop (FITL)
- Video switching
- Channelized and Unchannelized DS3 applications
- Audio signal routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- SONET
- Audio/video switches
- Relay replacements
- Precision data acquisition
