MAX391CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MAX391 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX391CPE Overview
This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. To ensure high reliability, a new packaging method Tube is used. It is mounted in the position Through Hole. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Extended operating temperature around 0°C~70°C TA. The total number of terminations is 16. High-quality output is provided by the electronic component's 1 channels. Turning on and running the electrical part should be easy with a 5V voltage supply. The electronic part body is injected with 16 pins. Multiplexers built on a SPST - NC switching circuit are built. There are 4 circuits in this switch device. Try searching with MAX391 if you're looking for variants. As far as internal resistance is concerned, it has 35Ohm. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 15V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. There should be 3V voltage fed to the electrical part below 3V. For this digital switch to work, 1μA current would suffice. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 8VYou should attach at least 3V voltage if you are using dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating voltages of 8V are compatible with the electrical part.
MAX391CPE Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX391CPE Applications
There are a lot of Maxim Integrated MAX391CPE Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Automatic test equipment
- PDAs
- Cell phones
- Precision instrumentation
- Medical systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- HDTV
- Fault Tolerant Systems
- Intelligent PBX
