MAX391CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX391 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| On-State Resistance (Max) | 35Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 75ns |
| Normal Position | NC |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
MAX391CPE+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). This high-reliability packaging method uses advanced packaging methods Tube. In Through Hole, you'll find this switch device. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of 0°C~70°C TA degrees Celsius. Totally, there are 16 terminations. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Circuits based on SPST - NC switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 4. Try searching with MAX391 to find analog multiplexer variants. This digital multiplexer has 35Ohm internal resistance. This switch device is a typical Multiplexer or Switches. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX391CPE+ Features
1 Channels
Switch Circuit: SPST - NC
MAX391CPE+ Applications
There are a lot of Maxim Integrated MAX391CPE+ Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- CSU
- PBX interfaces
- Switching Systems
- High-Voltage
- SONET/SDH ADM
- Fiber In The Loop (FITL)
- DVD-R
- Battery-powered systems
- Industrial and process control systems
