Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Weight |
665.986997mg |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX391 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Number of Channels |
4 |
Max Supply Voltage |
15V |
Min Supply Voltage |
3V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
130 ns |
Voltage - Supply, Single/Dual (±) |
3V~15V ±3V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
75 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
3V |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
130ns, 75ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height |
1.5mm |
Length |
10mm |
Width |
4mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
MAX391CSE+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around 0°C~70°C TA. Totally, there are 16 terminations. As a result of its 4 channels, this electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 16 series. SPST - NC switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with MAX391. A 35Ohm internal resistance characterizes this multiplexer. The datasheets for the 16 pins explain the functions. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 15V. A analog switch ic that has a cost-effective Dual, Single supply type. The lowest voltage fed to the electronic component should be 3V. 1μA current would be enough for this multiplexer to operate. When the digital multiplexer is charged above 1μA, damage can occur. Despite this switch device's dual supply capability, its voltage should not exceed 8V. For dual power supplies, a voltage of at least 3V should be attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX391CSE+ Features
4 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX391CSE+ Applications
There are a lot of Maxim Integrated MAX391CSE+ Analog Switches & Multiplexers ICs applications.
- Relay Replacement
- SDH
- Data switching
- Ultrasound
- Data Acquisition Systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Audio and video routing
- Fiber In The Loop (FITL)
- Automatic test equipment
- PCMCIA cards