Parameters |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
130ns |
Switch-off Time-Max |
75ns |
Normal Position |
NO |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2007 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
245 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX391 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
3.3/5/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
15V |
Min Supply Voltage |
3V |
Operating Supply Current |
1μA |
Throw Configuration |
SPST |
Voltage - Supply, Single/Dual (±) |
3V~15V ±3V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
130ns, 75ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
MAX391CUE Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. The operating temperature is extended to around 0°C~70°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. The electrical component body receives 16 pins. These analog multiplexers are built based on SPST - NC switching circuits. A 4 circuit is present in this switch device. Try searching for the analog switch ic with MAX391 if you are looking for variants. It has an internal resistance of 35Ohm. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 15V. The digital multiplexer has a low cost Dual, Single supply. 3V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 1μA current. There is no problem with using dual supply voltage, but it should not exceed 8V. The voltage should be at least 3V if you are using dual power supplies. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX391CUE Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX391CUE Applications
There are a lot of Maxim Integrated MAX391CUE Analog Switches & Multiplexers ICs applications.
- SONET
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- E1 Multiplexer
- Relay Replacement
- Battery Powered Instruments
- Communications systems
- Data switching
- Medical Instrumentation
- Cross Connects
- Low-Voltage