MAX391EPE
| Parameters | |
|---|---|
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MAX391 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 130ns |
| Switch-off Time-Max | 75ns |
| Normal Position | NC |
MAX391EPE Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. In Through Hole, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operational temperature extended around -40°C~85°C TA. In total, there are 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. Electronic part bodies are injected with 16 pins. Unlike digital switches, these are based on SPST - NC switching circuits. A 4 circuit is present in this switch device. Try searching with MAX391 if you're looking for variants. A 35Ohm internal resistance characterizes this multiplexer. The analog multiplexer shown here is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 15V. Analog switch ics with Dual, Single supply type are cost-effective. It is recommended to use 3V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 8V. When using dual power supplies, you should attach at least 3V. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX391EPE Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX391EPE Applications
There are a lot of Maxim Integrated MAX391EPE Analog Switches & Multiplexers ICs applications.
- Fiber to the Home
- Battery-powered systems
- USB 1.1 signal switching circuits
- ATM
- Remote wireless modules
- Industrial and process control systems
- Sample hold systems
- Channelized and Unchannelized DS3 applications
- Fault Tolerant Systems
- Residential Gateways, Home Gateway/Router
