MAX391ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX391 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX391ESE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 16. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. There are 16 pins injected into the electronic part body. Based on SPST - NC switching circuits, these analog multiplexers work. It consists of 4 circuits. Try searching with MAX391 to find analog multiplexer variants. A 35Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. Multiplexers should not be powered above 15V in normal situations. Analog switch ics with Dual, Single supply type are cost-effective. There should be 3V voltage fed to the electrical part below 3V. The switch device would be able to operate with 1μA current. The analogue multiplexer may be damaged if voltage is greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 8V. If you are using dual power supplies, you should attach at least 3V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. The electronic component can function from 8V.
MAX391ESE+T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX391ESE+T Applications
There are a lot of Maxim Integrated MAX391ESE+T Analog Switches & Multiplexers ICs applications.
- Power routing
- Sample hold systems
- Cable Modem
- SONET
- ISDN NT1/TA
- Avionics
- Sample-and-hold systems
- Medical systems
- DSUs
- Public switching systems
