MAX391EUE+T
| Parameters | |
|---|---|
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX391 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Power Supplies | 3.3/5+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
MAX391EUE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 1:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. The electrical component body receives 16 pins. Circuits based on SPST - NC switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 4. Try searching with MAX391 to find analog multiplexer variants. It has an internal resistance of 35Ohm. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 15V voltage to the switch device. 3V should be the lowest voltage fed to the electronic component. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 8V. With dual power supplies, you should attach at least 3V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electronic component can function from 8V.
MAX391EUE+T Features
1 Channels
Switch Circuit: SPST - NC
MAX391EUE+T Applications
There are a lot of Maxim Integrated MAX391EUE+T Analog Switches & Multiplexers ICs applications.
- Relay replacements
- HDTV
- Audio and video signal routing
- Cable Modem
- Private Branch Exchange (PBX)
- PCMCIA cards
- Wireless Local Loop
- ATM
- Modems
- Microprocessor Controlled Analog Systems
