MAX392CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX392 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| On-State Resistance (Max) | 35Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 130ns |
| Switch-off Time-Max | 75ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
MAX392CSE+ Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tube. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. The operating temperature is extended to around 0°C~70°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. This electronic part can be found in the 16 series. Unlike digital switches, these are based on SPST - NO switching circuits. 4 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with MAX392. For functions related to 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
MAX392CSE+ Features
1 Channels
Switch Circuit: SPST - NO
MAX392CSE+ Applications
There are a lot of Maxim Integrated MAX392CSE+ Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Medical
- Video signal routing
- Intelligent PBX
- New designs requiring multiplexer functions
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Remote Powered Equipment
- SDH
- Channel Banks
- High reliability control systems
