MAX392CUE+

130ns, 75ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX392 16 Pins 100pA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX392CUE+
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 700
Description: 130ns, 75ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX392 16 Pins 100pA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	175Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	842mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Base Part Number	MAX392
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	8V
Power Supplies	3.3/5/+-5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	15V
Min Supply Voltage	3V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	125 ns
Voltage - Supply, Single/Dual (±)	3V~15V ±3V~8V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	400 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	3V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	130ns, 75ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	130ns
Switch-off Time-Max	75ns
Normal Position	NC
Height Seated (Max)	1.1mm
Length	5mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

MAX392CUE+ Overview

Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of 0°C~70°C TA degrees Celsius. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 1 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. There are 16 pins injected into the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. This multiplexer is composed of 4 circuits. Try searching with MAX392 to find analog multiplexer variants. As far as internal resistance is concerned, it has 175Ohm. Datasheets for functions of 16 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 15V to the switch device in normal circumstances. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended to use 3V as the lowest voltage for the electrical part. For this multiplexer to operate, 1μA current would be sufficient. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 8V. It is recommended that you attach at least 3V to your dual power supply. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 8V operating voltages can be used with this electrical part.