Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX392 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Operating Supply Voltage |
8V |
Power Supplies |
3.3/5/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
15V |
Min Supply Voltage |
3V |
Operating Supply Current |
1μA |
Nominal Supply Current |
1μA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
125 ns |
Voltage - Supply, Single/Dual (±) |
3V~15V ±3V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
400 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
3V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
130ns, 75ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
130ns |
Switch-off Time-Max |
75ns |
Normal Position |
NC |
Height Seated (Max) |
1.1mm |
Length |
5mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX392CUE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around 0°C~70°C TA. The total number of terminations is 16. A high-quality output is provided by the electrical component's 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 16 series. SPST - NO switching circuits are used in these analog switch ics. Circuits number 4 make up this analogue multiplexer. Try searching for the analog switch ic with MAX392 if you are looking for variants. It has an internal resistance of 35Ohm. You can find the functions of the 16 pins in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 15V voltage to the switch device. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 3V should be the lowest voltage fed to the electronic component. 1μA current would be enough for this multiplexer to operate. Putting voltage greater than 1μA on the multiplexer may cause damage. If put voltage greater than 8V on the multiplexer, damage may be caused to the device. You should attach at least 3V voltage if you are using dual power supply. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer. A voltage of 8V can be used to operate the electronic component.
MAX392CUE+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX392CUE+T Applications
There are a lot of Maxim Integrated MAX392CUE+T Analog Switches & Multiplexers ICs applications.
- Medical Instrumentation
- Intelligent PBX
- High-Voltage
- Routers
- Battery-powered systems
- Audio signal routing
- Medical systems
- Access Concentrators
- Digital access cross connects
- Precision instrumentation