MAX392ESE

130ns, 75ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX392 16 Pins 100pA 5V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX392ESE
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 146
Description: 130ns, 75ns SPST - NO 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX392 16 Pins 100pA 5V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Contact Plating	Tin
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2007
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	35Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	245
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	1.27mm
Base Part Number	MAX392
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	8V
Polarity	Non-Inverting
Number of Channels	4
Max Supply Voltage	15V
Min Supply Voltage	3V
Operating Supply Current	1μA
Nominal Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	125 ns
Voltage - Supply, Single/Dual (±)	3V~15V ±3V~8V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	400 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	3V
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	130ns, 75ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	130ns
Switch-off Time-Max	75ns
Normal Position	NO
Height	1.5mm
Length	10mm
Width	4mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

MAX392ESE Overview

Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tube is used to provide high reliability. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operating temperature extended to -40°C~85°C TA. A total of 16 terminations have been recorded. The electronic part delivers high-quality output through its 4 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. An injection of 16 pins is performed into the body of the electrical component. The analog switch ics are built using SPST - NO switching circuits. Look for analog switch ic variants by searching with MAX392. As far as internal resistance is concerned, it has 35Ohm. Please refer to the datasheets for 16 pins functions. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 15V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 3V. The switch device would be able to operate with 1μA current. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 8V. A dual power supply should have at least 3V voltage attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. Operating voltages of 8V are compatible with the electrical part.