MAX392EUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX392 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 125 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 130ns |
| Switch-off Time-Max | 75ns |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX392EUE+T Overview
The electrical component comes in 16-TSSOP (0.173, 4.40mm Width) packaging, which makes it convenient to ship overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. The operating temperature is extended to around -40°C~85°C TA. There are 16 terminations totally. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 5V voltage supply. It is injected into the electrical part body with 16 pins. These analog multiplexers are built based on SPST - NO switching circuits. The multiplexer consists of 4 circuits. Use MAX392 to search for variants of the digital switches. It has an internal resistance of 35Ohm. For details about the functions of 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 15V should not normally be supplied to the switches. It is recommended that the electrical component receives a voltage of 3V. A digital multiplexer may suffer damage if voltage is applied above 1μA. There is no problem with using dual supply voltage, but it should not exceed 8V. You should attach at least 3V voltage if you are using dual power supply. This analog switch ic utilizes SEPARATE OUTPUT output. 8V operating voltages can be used with this electrical part.
MAX392EUE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX392EUE+T Applications
There are a lot of Maxim Integrated MAX392EUE+T Analog Switches & Multiplexers ICs applications.
- Voice over IP/DSL – Integrated Access Devices, Smart
- New designs requiring multiplexer functions
- Automatic test equipment
- Relay replacements
- Data Acquisition Systems
- Digital Cross-Connects
- High speed data transmission line cards
- Switching Systems
- Multi-Line E1 Interface Cards
- Access Concentrators
