MAX393CPE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MAX393 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MAX393CPE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). A high level of reliability can be achieved through the use of an advanced packaging method Tube. This analog switch is mounted in Through Hole. There is 1:1 ratio between the number of multiplexers and demultiplexers. The operating temperature is extended to around 0°C~70°C TA. There are 16 terminations totally. A 1 channel electronic part produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPST - NO/NC switching circuits. A 4 circuit is present in this switch device. Using the MAX393 search parameter, you can discover variants of the switch. This digital multiplexer has 35Ohm internal resistance. To find out what the functions of 16 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. Users shouldn't supply more than 15V voltage to the switch device. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 3V. An operating current of 1μA would be sufficient for this switch device. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 8V. For dual power supplies, a voltage of at least 3V should be attached. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. 8V operating voltages can be used with this electrical part.
MAX393CPE+ Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX393CPE+ Applications
There are a lot of Maxim Integrated MAX393CPE+ Analog Switches & Multiplexers ICs applications.
- USB 1.1 signal switching circuits
- Medical systems
- Industrial and process control systems
- Power routing
- DSUs
- Optical Applications
- Audio and video routing
- Switching Systems
- Automatic test equipment
- PBX interfaces
