MAX393CSE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 665.986997mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX393 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Number of Channels | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX393CSE+ Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tube. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 1:1. Around 0°C~70°C TA is the extended operating temperature. In total, there are 16 terminations. Due to its 4 channels, the electrical component produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPST - NO/NC switching circuits. Try searching for the analog switch ic with MAX393 if you are looking for variants. There is 35Ohm internal resistance in this digital multiplexer. For details about the functions of 16 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 15V. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 3V. This multiplexer would work with 1μA current. Putting voltage greater than 1μA on the multiplexer may cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 8V. If you are using a dual power supply, you should attach at least 3V. There are SEPARATE OUTPUT outputs on this analog switch ic.
MAX393CSE+ Features
4 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX393CSE+ Applications
There are a lot of Maxim Integrated MAX393CSE+ Analog Switches & Multiplexers ICs applications.
- MP3 players
- Mechanical reed relay replacement
- SONET
- Private Branch Exchange (PBX)
- SONET/SDH ADM
- Automatic test equipment
- Digital cross connects (DSX-1)
- Power routing
- E1 Network Equipment
- Channelized and Unchannelized DS3 applications
