Parameters |
Factory Lead Time |
1 Week |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2007 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
MAX393 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Qualification Status |
Not Qualified |
Power Supplies |
3.3/5/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Voltage - Supply, Single/Dual (±) |
3V~15V ±3V~8V |
Neg Supply Voltage-Nom (Vsup) |
-5V |
On-State Resistance (Max) |
35Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
72 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
On-state Resistance Match-Nom |
0.3Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
130ns, 75ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
130ns |
Switch-off Time-Max |
75ns |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
RoHS Status |
ROHS3 Compliant |
MAX393CSE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of 0°C~70°C TA degrees Celsius. Total terminations are 16. A high-quality output is provided by the electrical component's 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. An injection of 16 pins is performed into the body of the electrical component. Unlike digital switches, these are based on SPST - NO/NC switching circuits. 4 circuits are used in this analogue multiplexer. Try searching with MAX393 to find analog multiplexer variants. Multiplexer or Switches is a typical switch device. A total of SEPARATE OUTPUT outputs are available on this analog switch ic.
MAX393CSE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX393CSE+T Applications
There are a lot of Maxim Integrated MAX393CSE+T Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- Intelligent PBX
- Medical Instrumentation
- Voice over IP/DSL – Integrated Access Devices, Smart
- Channel Banks
- Cable Modem
- Battery-powered systems
- USB 1.1 signal switching circuits
- Communications systems
- Relay Replacement