MAX393CUE+T

130ns, 75ns SPST - NO/NC 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX393 16 Pins 100pA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX393CUE+T
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 232
Description: 130ns, 75ns SPST - NO/NC 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX393 16 Pins 100pA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2007
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
Resistance	35Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Base Part Number	MAX393
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	8V
Power Supplies	3.3/5/+-5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	15V
Min Supply Voltage	3V
Operating Supply Current	1μA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	130 ns
Voltage - Supply, Single/Dual (±)	3V~15V ±3V~8V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	75 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	3V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	72 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	9pF 9pF
On-state Resistance Match-Nom	0.3Ohm
Switch Circuit	SPST - NO/NC
Switch Time (Ton, Toff) (Max)	130ns, 75ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height Seated (Max)	1.1mm
Length	5mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX393CUE+T Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Around 0°C~70°C TA is the extended operating temperature. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component of this type can be found in the 16 series. Based on SPST - NO/NC switching circuits, these analog multiplexers work. A total of 4 circuits make up this switch device. Try searching for MAX393 variants of the analog switch ic. In this multiplexer, the internal resistance is 35Ohm. To find out what the 16 pins do, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 15V to a switch device. Dual, Single supply type digital switch with a low cost. 3V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 1μA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 8V. The voltage should be at least 3V if you are using dual power supplies. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Operating voltages of 8V are compatible with the electrical part.