MAX393EPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 245 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Base Part Number | MAX393 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 130ns |
| Switch-off Time-Max | 75ns |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX393EPE Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-DIP (0.300, 7.62mm). Advanced packaging method Tube is used to provide high reliability. In Through Hole, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 1:1. Operating temperature extended to -40°C~85°C TA. In total, 16 terminations have occurred. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. The electronic part body is injected with 16 pins. A SPST - NO/NC switching circuit is used to build these analog multiplexers. The multiplexer consists of 4 circuits. Search with MAX393 if you are looking for analog multiplexer variants. There is 35Ohm internal resistance in this digital multiplexer. You can find the functions of the 16 pins in the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 15V in normal situations. It is recommended that the electrical component receives a voltage of 3V. Despite this switch's dual supply capability, its voltage should not exceed 8V. A dual power supply should have at least 3V voltage attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them.
MAX393EPE Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX393EPE Applications
There are a lot of Maxim Integrated MAX393EPE Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Relay replacements
- Sample-and-hold systems
- Communications systems
- Microprocessor Controlled Analog Systems
- Precision data acquisition
- Frame Relay Equipment
- Audio and video switching
- Mechanical reed relay replacement
- Communication systems
