MAX393EUE+T
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 35Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 696mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX393 |
| Pin Count | 16 |
| Operating Supply Voltage | 8V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 15V |
| Min Supply Voltage | 3V |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±3V~8V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 3V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.3Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 300m Ω |
| Crosstalk | -85dB @ 1MHz |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX393EUE+T Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component like this is included in the 16 series. Multiplexers built on a SPST - NO/NC switching circuit are built. The circuits in this analogue multiplexer number 4. Search with MAX393 if you are looking for analog multiplexer variants. This digital multiplexer has 35Ohm internal resistance. You can find the functions of the 16 pins in the datasheets. normally, users should not supply switches with voltages higher than 15V. A low voltage of 3V should be applied to the electronic component. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. Despite this switch's dual supply capability, its voltage should not exceed 8V. When using dual power supplies, you should attach at least 3V. The electrical part can be operated at 8V voltage levels.
MAX393EUE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX393EUE+T Applications
There are a lot of Maxim Integrated MAX393EUE+T Analog Switches & Multiplexers ICs applications.
- Public switching systems
- Medical systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Microwave transmission systems
- Wireless Local Loop
- Precision instrumentation
- Central office
- RGB switches
- DVD-R
- PDAs
