Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-SSOP (0.209, 5.30mm Width) |
Number of Pins |
20 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
2008 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
ECCN Code |
EAR99 |
Resistance |
35Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Base Part Number |
MAX394 |
Output |
SEPARATE OUTPUT |
Pin Count |
20 |
Operating Supply Voltage |
8V |
Power Supplies |
3.3/5/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
16V |
Min Supply Voltage |
2.4V |
Operating Supply Current |
1μA |
Nominal Supply Current |
60nA |
Max Supply Current |
60nA |
Turn On Delay Time |
130 ns |
Voltage - Supply, Single/Dual (±) |
2.7V~15V ±2.7V~8V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
75 ns |
Max Dual Supply Voltage |
8V |
On-State Resistance (Max) |
35Ohm |
Min Dual Supply Voltage |
2.4V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
66 dB |
Current - Leakage (IS(off)) (Max) |
200pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 12pF |
On-state Resistance Match-Nom |
0.5Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
130ns, 75ns |
Charge Injection |
5pC |
Channel-to-Channel Matching (ΔRon) |
500m Ω |
Crosstalk |
-88dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
1.99mm |
Length |
7.2mm |
Width |
5.29mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX394CAP+ Overview
The electrical component comes in 20-SSOP (0.209, 5.30mm Width) packaging, which makes it convenient to ship overseas. High reliability is provided by advanced packaging method Tube. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operation at a temperature around 0°C~70°C TA. Totally, there are 20 terminations. As a result of its 1 channels, this electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 20 series that this electronic component is included. SPDT switching circuits are used in these analog switch ics. There are 4 circuits in this switch device. Search with MAX394 if you are looking for analog multiplexer variants. This digital multiplexer has 35Ohm internal resistance. The functions of 20 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. Digital switch that provides Dual, Single power at a cost-effective price. There should be 2.4V voltage fed to the electrical part below 2.4V. For this digital switch to work, 1μA current would suffice. The analogue multiplexer may be damaged if voltage is greater than 60nA. For this switch, a dual supply voltage is feasible, but it must not exceed 8VThe voltage should be at least 2.4V if you are using dual power supplies. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. 8V operating voltages are supported by the electronic component.
MAX394CAP+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX394CAP+ Applications
There are a lot of Maxim Integrated MAX394CAP+ Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Battery Powered Systems
- Multi-Line E1 Interface Cards
- Audio and video routing
- Cable PC
- Optical Applications
- Wireless Local Loop
- Automotive applications
- USB 1.1 signal switching circuits
- Fault Tolerant Systems