MAX394CAP+T

130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-SSOP (0.209, 5.30mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX394CAP+T
Package: 20-SSOP (0.209, 5.30mm Width)
Datasheet: PDF
Stock: 111
Description: 130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-SSOP (0.209, 5.30mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	20-SSOP (0.209, 5.30mm Width)
Number of Pins	20
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	2006
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	20
Resistance	35Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	842mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX394
Output	SEPARATE OUTPUT
Pin Count	20
Operating Supply Voltage	8V
Power Supplies	3.3/5/+-5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	16V
Min Supply Voltage	2.4V
Operating Supply Current	1μA
Nominal Supply Current	60nA
Max Supply Current	60nA
Turn On Delay Time	130 ns
Voltage - Supply, Single/Dual (±)	2.7V~15V ±2.7V~8V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	75 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	2.4V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	66 dB
Current - Leakage (IS(off)) (Max)	200pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	0.5Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	130ns, 75ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	500m Ω
Crosstalk	-88dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height Seated (Max)	1.99mm
Length	7.2mm
Width	5.29mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX394CAP+T Overview

The electronic component is convenient to ship overseas because it is packed in a 20-SSOP (0.209, 5.30mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. 2:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around 0°C~70°C TA. In total, 20 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. A 5V voltage supply should turn on and run the electronic component. There is an electrical component included in the 20 series. Unlike digital switches, these are based on SPDT switching circuits. There are 4 circuits in this switch device. Try searching with MAX394 if you're looking for variants. As far as internal resistance is concerned, it has 35Ohm. To find out what the functions of 20 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 16V volts for the multiplexer. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended to use 2.4V as the lowest voltage for the electrical part. An operating current of 1μA would be sufficient for this switch device. Put voltage above 60nA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 8V. With dual power supplies, you should attach at least 2.4V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. 8V operating voltages are supported by the electronic component.