MAX394CWP+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 35Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX394 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 8V |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 60nA |
| Max Supply Current | 60nA |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~15V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
| Min Dual Supply Voltage | 2.4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 66 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 2.35mm |
| Length | 13mm |
| Width | 7.6mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX394CWP+ Overview
Presented in 20-SOIC (0.295, 7.50mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tube is used. In Surface Mount, this analog switch is mounted. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operating temperature around 0°C~70°C TA extended. There are 20 terminations totally. The electronic part delivers high-quality output through its 4 channels. An 5V voltage supply should allow the electrical part to be turned on and run. A total of 20 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPDT switching circuits. Try searching for the analog switch ic with MAX394 if you are looking for variants. It has an internal resistance of 35Ohm. The functions of 20 pins can be found in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 16V in normal situations. An effective Dual, Single supply digital multiplexer. 2.7V is the lowest voltage the electrical component should receive. This digital switch can be operated with a current of 1μA. It may damage the digital multiplexer if the voltage is higher than 60nA. There is no problem with using dual supply voltage, but it should not exceed 8V. You should attach at least 2.4V voltage if you are using dual power supply. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. It can operate from 8V operating voltages.
MAX394CWP+ Features
4 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX394CWP+ Applications
There are a lot of Maxim Integrated MAX394CWP+ Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- ATM
- Industrial and process control systems
- Battery Powered Instruments
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Video switching
- Ultrasound
- PBXs
- Public switching systems
- Automotive applications
