MAX394EAP

130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-SSOP (0.209, 5.30mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX394EAP
Package: 20-SSOP (0.209, 5.30mm Width)
Datasheet: PDF
Stock: 660
Description: 130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-SSOP (0.209, 5.30mm Width)(Kg)

Details

Tags

Parameters
Turn On Delay Time	130 ns
Voltage - Supply, Single/Dual (±)	2.7V~15V ±2.7V~8V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	75 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	2.4V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	66 dB
Current - Leakage (IS(off)) (Max)	200pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	0.5Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	130ns, 75ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	500m Ω
Crosstalk	-88dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height Seated (Max)	1.99mm
Length	7.2mm
Width	5.29mm
Radiation Hardening	No
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	20-SSOP (0.209, 5.30mm Width)
Number of Pins	20
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2005
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	20
Resistance	65Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Subcategory	Multiplexer or Switches
Max Power Dissipation	842mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	245
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Base Part Number	MAX394
Output	SEPARATE OUTPUT
Pin Count	20
Operating Supply Voltage	8V
Power Supplies	3.3/5/+-5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	16V
Min Supply Voltage	2.4V
Operating Supply Current	100nA
Nominal Supply Current	60nA
Max Supply Current	60nA

MAX394EAP Overview

Presented in 20-SSOP (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Total terminations are 20. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. An electrical component of this type can be found in the 20 series. A SPDT switching circuit is used for these analog switches. 4 circuits are used in this analogue multiplexer. Try searching with MAX394 if you're looking for variants. The internal resistance of this digital multiplexer is 65Ohm. Please refer to the datasheets for 20 pins functions. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 16V volts for the multiplexer. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended that the electrical component receives a voltage of 2.4V. For this multiplexer to operate, 100nA current would be sufficient. The switch multiplexer may be damaged if it is exposed to voltage greater than 60nA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 8V. In the case of dual power supplies, you should connect at least 2.4V. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Operating voltages range from 8V.