MAX394EAP+T
| Parameters | |
|---|---|
| Min Dual Supply Voltage | 2.4V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 66 dB |
| Current - Leakage (IS(off)) (Max) | 200pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 12pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 130ns, 75ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -88dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.99mm |
| Length | 7.2mm |
| Width | 5.29mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 65Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX394 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Operating Supply Voltage | 8V |
| Power Supplies | 3.3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 2.4V |
| Operating Supply Current | 100nA |
| Nominal Supply Current | 60nA |
| Max Supply Current | 60nA |
| Turn On Delay Time | 130 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~15V ±2.7V~8V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 8V |
| On-State Resistance (Max) | 35Ohm |
MAX394EAP+T Overview
Shipping overseas is convenient due to the electrical component's packing in 20-SSOP (0.209, 5.30mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature around -40°C~85°C TA extended. The total number of terminations is 20. Due to its 1 channels, the electrical component produces high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. This electrical component is included in the 20 series of products. A SPDT switching circuit is used to build these analog multiplexers. There are 4 circuits in this multiplexer. Try searching with MAX394 if you're looking for variants. As far as internal resistance is concerned, it has 65Ohm. For functions related to 20 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. normally, users should not supply switches with voltages higher than 16V. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2.4V. This multiplexer would work with 100nA current. When the digital multiplexer is charged above 60nA, damage can occur. Despite this switch's dual supply capability, its voltage should not exceed 8V. For dual power supplies, a voltage of at least 2.4V should be attached. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. Operating voltages range from 8V.
MAX394EAP+T Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
MAX394EAP+T Applications
There are a lot of Maxim Integrated MAX394EAP+T Analog Switches & Multiplexers ICs applications.
- SONET
- DSLAMs
- Industrial
- Audio and video routing
- Audio signal routing
- New designs requiring multiplexer functions
- Automotive applications
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- ATM
- Data Acquisition Systems
