MAX394EUP+

130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-TSSOP (0.173, 4.40mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX394EUP+
Package: 20-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 528
Description: 130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	20-TSSOP (0.173, 4.40mm Width)
Number of Pins	20
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2008
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	20
ECCN Code	EAR99
Resistance	35Ohm
Terminal Finish	MATTE TIN
Subcategory	Multiplexer or Switches
Max Power Dissipation	842mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.65mm
Base Part Number	MAX394
Output	SEPARATE OUTPUT
Pin Count	20
Operating Supply Voltage	8V
Power Supplies	3.3/5/+-5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	16V
Min Supply Voltage	2.7V
Operating Supply Current	100nA
Nominal Supply Current	60nA
Max Supply Current	60nA
Turn On Delay Time	130 ns
Voltage - Supply, Single/Dual (±)	2.7V~15V ±2.7V~8V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	75 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	2.4V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	66 dB
Current - Leakage (IS(off)) (Max)	200pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	0.5Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	130ns, 75ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	500m Ω
Crosstalk	-88dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height Seated (Max)	1.1mm
Length	6.5mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	ROHS3 Compliant

MAX394EUP+ Overview

Presented in 20-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature extended to -40°C~85°C TA. In total, 20 terminations have occurred. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. Electronic part bodies are injected with 20 pins. A SPDT switching circuit is used to build these analog multiplexers. There are 4 circuits in this switch device. Use MAX394 to search for variants of the digital switches. Analog switches have 35Ohm internal resistance. To find out what the functions of 20 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 16V. Analog switch ics with Dual, Single supply type are cost-effective. 2.7V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 100nA current. If put voltage greater than 60nA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 8V. With dual power supplies, you should attach at least 2.4V. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The electrical part can be operated at 8V voltage levels.