MAX394EWP

130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-SOIC (0.295, 7.50mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX394EWP
Package: 20-SOIC (0.295, 7.50mm Width)
Datasheet: PDF
Stock: 691
Description: 130ns, 75ns SPDT 35Ohm Analog Switches BREAK-BEFORE-MAKE MAX394 20 Pins 200pA 5V 20-SOIC (0.295, 7.50mm Width)(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	20-SOIC (0.295, 7.50mm Width)
Number of Pins	20
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	2005
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	20
ECCN Code	EAR99
Resistance	35Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Subcategory	Multiplexer or Switches
Max Power Dissipation	842mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	245
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	1.27mm
Base Part Number	MAX394
Output	SEPARATE OUTPUT
Pin Count	20
Operating Supply Voltage	8V
Power Supplies	3.3/5/+-5V
Number of Channels	4
Max Supply Voltage	16V
Min Supply Voltage	2.7V
Operating Supply Current	100nA
Nominal Supply Current	60nA
Max Supply Current	60nA
Turn On Delay Time	130 ns
Voltage - Supply, Single/Dual (±)	2.7V~15V ±2.7V~8V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	75 ns
Max Dual Supply Voltage	8V
On-State Resistance (Max)	35Ohm
Min Dual Supply Voltage	2.4V
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	66 dB
Current - Leakage (IS(off)) (Max)	200pA
Channel Capacitance (CS(off), CD(off))	12pF 12pF
On-state Resistance Match-Nom	0.5Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	130ns, 75ns
Charge Injection	5pC
Channel-to-Channel Matching (ΔRon)	500m Ω
Crosstalk	-88dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Height Seated (Max)	2.65mm
Length	12.8mm
Width	7.5mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

MAX394EWP Overview

The electronic component is convenient to ship overseas because it is packed in a 20-SOIC (0.295, 7.50mm Width). High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 20. This electronic part offers high-quality output due to its 4 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. This electrical component is included in the 20 series of products. Based on SPDT switching circuits, these analog multiplexers work. Try searching with MAX394 if you're looking for variants. Analog switches have 35Ohm internal resistance. You can find the functions of the 20 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 16V. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 2.7V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 100nA current. The analogue multiplexer may be damaged if voltage is greater than 60nA. For this multiplexer, dual supply voltage is feasible, but it should not exceed 8V. For dual power supplies, a voltage of at least 2.4V should be attached. There are SEPARATE OUTPUT outputs on this analog switch ic. This electrical part is compatible with 8V operating voltages.